Exactly How To Install A Bath Tub (For Novices).
Make An AppointmentThe article author is making a number of good annotation on the subject of How to Install a Bathtub in general in this post below.
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is easily accessible, the job can move immediately; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to vacate the old bathtub and embeded in the new one. See to it you have certified yourself for the work and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you start. Possibilities are you might need a specialist plumber to make tube links.
This short article will certainly help you mount a new tub in your washroom if you have already acquired a new bathtub and don't require to change the plan of your previous water pipes.
Your devices and also material list need to comprise the following:
Preparing for the Setup
To start with, the supporting frame provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to prevent stress on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of removing the existing taps can be fairly bothersome because of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Utilizing both wood boards under its feet, place the tub in the needed placement. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost adaptable tap connector to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply as well as check all joints as well as brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as also inspect the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the bath tub has actually been used at the very least once as this will resolve it right into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet as well as the sink. Safeguard the faucet in position with the maker provided backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes as well as cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can break fairly early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading up on Installing A Bathtub? Create feedback down the page. We'd be pleased to see your reactions about this piece. We hope that you visit us again before long. Enjoyed reading our piece of writing? Please share it. Help somebody else discover it. Thanks for going through it.
Check It Out